JN0-360 latest Juniper certification exam questions and answers published

In order to pass Juniper certification JN0-360 exam, selecting the appropriate training tools is very necessary. And professional study materials about Juniper certification JN0-360 exam is a very important part. Our ITCertKing can have a good and quick provide of professional study materials about Juniper certification JN0-360 exam. Our ITCertKing IT experts are very experienced and their study materials are very close to the actual exam questions, almost the same. ITCertKing is a convenient website specifically for people who want to take the certification exams, which can effectively help the candidates to pass the exam.

You can free download part of ITCertKing's practice questions and answers about Juniper certification JN0-360 exam online. Once you decide to select ITCertKing, ITCertKing will make every effort to help you pass the exam. If you find that our exam practice questions and answers is very different form the actual exam questions and answers and can not help you pass the exam, we will immediately 100% full refund.

A lot of IT people want to pass Juniper certification JN0-360 exams. Thus they can obtain a better promotion opportunity in the IT industry, which can make their wages and life level improved. But in order to pass Juniper certification JN0-360 exam many people spent a lot of time and energy to consolidate knowledge and didn't pass the exam. This is not cost-effective. If you choose ITCertKing's product, you can save a lot of time and energy to consolidate knowledge, but can easily pass Juniper certification JN0-360 exam. Because ITCertKing's specific training material about Juniper certification JN0-360 exam can help you 100% pass the exam. If you fail the exam, ITCertKing will give you a full refund.

ITCertKing's practice questions and answers about the Juniper certification JN0-360 exam is developed by our expert team's wealth of knowledge and experience, and can fully meet the demand of Juniper certification JN0-360 exam's candidates. From related websites or books, you might also see some of the training materials, but ITCertKing's information about Juniper certification JN0-360 exam is the most comprehensive, and can give you the best protection. Candidates who participate in the Juniper certification JN0-360 exam should select exam practice questions and answers of ITCertKing, because ITCertKing is the best choice for you.

With ITCertKing's Juniper JN0-360 exam training materials, you can get the latest Juniper JN0-360 exam questions and answers. It can make you pass the Juniper JN0-360 exam. Juniper JN0-360 exam certification can help you to develop your career. ITCertKing's Juniper JN0-360 exam training materials is ensure that you fully understand the questions and issues behind the concept. t can help you pass the exam easily.

Exam Code: JN0-360
Exam Name: Juniper (Juniper Networks Certified Internet Specialist (JNCIS-SP))
One year free update, No help, Full refund!
Total Q&A: 252 Questions and Answers
Last Update: 2013-09-30

ITCertKing is a website which is able to speed up your passing the Juniper certification JN0-360 exams. Our Juniper certification JN0-360 exam question bank is produced by ITCertKing's experts's continuously research of outline and previous exam. When you are still struggling to prepare for passing the Juniper certification JN0-360 exams, please choose ITCertKing's latest Juniper certification JN0-360 exam question bank, and it will brings you a lot of help.

JN0-360 Free Demo Download: http://www.itcertking.com/JN0-360_exam.html

NO.1 You are logged into a router and have navigated to the (edit routing-options] level of the hierarchy. You
have been asked to create a static route that will use 10.10.10.1 as its primary next-hop and 10.10.10.5
as its secondary next-hop.
Which command correctly configures this scenario?
A.set static route 8/8 10.10.10.1 qualified-next-hop 10.10.10.5 pref 10
B.set static route 8/8 next-hop 10.10.10.1 secondary-next-hop 10.10.10.5 preference 10
C.set static route 8/8 next-hop 10.10.10.1 qualified-next-hop 10.10.10.5 preference 10
D.set static route 8/8 next-hop [10.10.10.1 10.10.10.5] pref 10
Answer: C

Juniper   JN0-360 demo   JN0-360   JN0-360   JN0-360 test answers

NO.2 Router A is an OSPF router connected to both Area 0 and Area 1 Area 1 has been configured as a stub
area Which two LSA types does Router A suppress from Area 1 ?
A.Router LSA
B.External LSA
C.Summary LSA
D.ASBR Summary LSA
Answer: B D

Juniper   JN0-360   JN0-360 test   JN0-360   JN0-360 test questions

NO.3 You are logged into a router and have navigated to the [edit routing-options] level of the hierarchy. You
have been asked to create a static route that will use 43 18 7 1 as its primary next-hop and 76 1310 2 as
its secondary next-hop.
Which command correctly configures this setup?
A.set static route 0/0 76.13.10.2 qualified-next-hop 43.18.7.1 pref 10
B.set static route 0/0 next-hop 43.18.7.1 secondary-next-hop 76.13.10.2 preference 10
C.set static route 0/0 next-hop [76.13.10.2 10.10.10.5] pref 10
D.set static route 0/0 next-hop 43.18.7.1 qualified-next-hop 76.13.10.2 preference 10
Answer: D

Juniper study guide   JN0-360   JN0-360 pdf   JN0-360

NO.4 Which two values displayed in the output from the show spanning-tree MSTP configuration command
must match on all switches participating in the same MSTP region? (Choose two)
A.root bridge identifier
B.authentication checksum
C.context identifier
D.configuration digest
Answer: CD

Juniper   JN0-360 exam dumps   JN0-360

NO.5 You must configure an OSPF area that does not accept type 3 link-state advertisements (LSAs) from
area 0 (other than the default route) You have configured your area to be stub, but you still see type 3
LSAs.
What will account for this behavior?
A.You should have configured your area as totally stubby
B.You should have used a not-so-stubby-area
C.You are experiencing a routing loop
D.You have exported routes into OSPF
Answer: A

Juniper practice test   JN0-360 questions   JN0-360 exam prep   JN0-360 demo   JN0-360

NO.6 You have been asked to configure an IPv6 address for a group of interfaces that could belong on
different routers. If a packet is sent to that address, it should be received by all routers in the group.
Which address type would be suited for these requirements?
A.Unicast
B.Multicast
C.Anycast
D.Broadcast
Answer: B

Juniper test   JN0-360   JN0-360 pdf   JN0-360 exam dumps   JN0-360   JN0-360 braindump

NO.7 Which IS-IS packet is used to determine the level of an IS-IS neighbor?
A.IIH
B.LSP
C.PSNP
D.CSNP
Answer: A

Juniper pdf   JN0-360   JN0-360   JN0-360

NO.8 Which BGP state denotes a fully operational session?
A.Established
B.Active
C.Operational
D.Connect
Answer: A

Juniper exam prep   JN0-360   JN0-360 dumps   JN0-360 exam simulations   JN0-360

NO.9 Which Junos operational mode command is used to verify that load balancing is working as expected?
A.show route all
B.show route extensive
C.show route balancing
D.show route forwarding-table
Answer: D

Juniper   JN0-360   JN0-360   JN0-360

NO.10 You have configured an IP-IP tunnel between Router A and Router B
Which Junos operational mode command is used to verify that the tunnel interface is up and operational?
A.show chassis tunnel status
B.show tunnel interface
C.show interfaces terse
D.show interfaces tunnel
Answer: C

Juniper   JN0-360 answers real questions   JN0-360 answers real questions   JN0-360 dumps

NO.11 Which two statements describe differences between IPv4 and IPv6.? (Choose two)
A.IPsec is built into IPv6
B.IPv6 uses a 32-bit (4-byte) address and can support up to 4,294,967,296 addresses
C.IPv4 supports extension headers whereas IPv6 options are integrated into the base
D.IPv6 eliminates the need for NAT
Answer: AD

Juniper certification training   JN0-360   JN0-360

NO.12 Which role does the router ID (RID) have in the BGP route selection process?
A.The router ID is evaluated immediately after MED to determine route preference
B.The router ID is evaluated last in the route selection process
C.The router ID is evaluated after the cluster length and a lower router ID is chosen
D.The router ID is evaluated after analyzing the IGP metric cost
Answer: C

Juniper   JN0-360 practice test   JN0-360

NO.13 Click the Exhibit button
Based on the illustration of the VPLS topology shown in the exhibit, which statement is true?
A.PE-C must have a spanning-tree protocol enabled
B.CE-C must have BGP enabled
C.Traffic forwarded from PE-C to PE-A is forwarded on to PE-B
D.Traffic forwarded from PE-C to PE-A is not forwarded on to PE-B
Answer: D

Juniper   JN0-360 test   JN0-360   JN0-360   JN0-360 pdf

NO.14 You have recently implemented a graceful Routing-Engine switchover (GRES) and want to further
reduce down time if a Routing Engine (RE) failure occurs.
Which two features can be configured on this device to reduce its downtime in this situation? (Choose
two)
A.VRRP
B.GR
C.BFD
D.NSR
Answer: B D

Juniper   JN0-360   JN0-360 certification   JN0-360 pdf

NO.15 What are two valid actions that can be applied to a frame by a Layer 2 firewall filter?
(Choose two)
A.Log
B.loss-priority
C.sample
D.count
Answer: BD

Juniper   JN0-360   JN0-360 exam   JN0-360   JN0-360   JN0-360

NO.16 Click the Exhibit button
You work for the regional Internet service provider shown in the exhibit You have a partial BGP table and
are receiving a 10 100/16 route from your upstream ISP You have been asked to configure a default route
that can be sent to your downstream customer This route should forward customer traffic toward your
upstream Tier 11SP as long as the 10.100/16 route is present.
What would accomplish this goal?
A.Create and announce an aggregate default route
B.Create and announce a static default route with a next-hop of discard
C.Create and announce a static default route with a next-hop of reject
D.Create and announce a generated default route
E.Create an advertise-map with exist-map
Answer: E

Juniper   JN0-360 dumps   JN0-360   JN0-360 questions

NO.17 Click the Exhibit button
In the exhibit, OSPF routers R1, R2, R3, and R4 come up, in order, at 1-minute intervals
Which router will be the designated router?.
A.R1
B.R2
C.R3
D.R4
Answer: A

Juniper   JN0-360 pdf   JN0-360 original questions   JN0-360 answers real questions

NO.18 What is the function of the hop limit field in the IPv6 header?
A.It limits the diameter of the network to 20 hops
B.It sets the number of hops in the network to be equal to the MPLS header time-to-live (TTL)
C.It replaces the time-to-live (TTL) field in IPv4
D.It represents future extensibility to the protocol
Answer: C

Juniper   JN0-360 certification   JN0-360 study guide   JN0-360

NO.19 Click the Exhibit button
Referring to the network illustrated in the exhibit, how does router A reach destinations in area 49.2222?
A.Router A will use the routes from area 49.2222; it learns from router B
B.Router A will see the attached bit from router B and create a default route
C.Router A must have a default route manually configured
D.Router A will receive a default route in the IS-IS update from router B
Answer: B

Juniper certification training   JN0-360   JN0-360 original questions

NO.20 You have been asked to define a default gateway for traffic leaving a router. This route should use
interface so-0/0/0 as its next-hop.Which type of route would be suited for this scenario?
A.a static route
B.a generated route
C.a martian route
D.an aggregate route
Answer: A

Juniper   JN0-360   JN0-360   JN0-360 practice test

ITCertKing offer the latest FCNSP.v5 exam material and high-quality HP2-H28 pdf questions & answers. Our 00M-620 VCE testing engine and E20-018 study guide can help you pass the real exam. High-quality MB3-700 dumps training materials can 100% guarantee you pass the exam faster and easier. Pass the exam to obtain certification is so simple.

Article Link: http://www.itcertking.com/JN0-360_exam.html